Sunday, 12 August 2012

Diesel Motor Crash Course


If you are growing weary of all our technical dramas starting out with “it all started out so simply”, then just imagine our frustration.  This one really did come out of nowhere, or to be more precise, from the cautionary tales of a fellow mariner who had a nasty surprise during his recent summer sailing trip.

Guru Bob, recently returned from the aforementioned trip, suggested that we check the pre-filter of our diesel engine to look for any rust particles that may be emanating from our 20-year-old “stainless steel” fuel tank that just might clog up a fuel line when you least expect it.  Since the fuel is of dubious origin (the Caribbean) and had been sitting in plastic jerry cans for over a year before being put in the tank, he also suggested we check for condensation.

Water pump impeller and gasket.
The engine has always been an element of moderate anxiety for us, and we were eager to get to know it a bit better before trusting it blindly in potentially dangerous situations.  Before tackling the fuel lines, we decided to start with something simple: checking the water pump impeller and gasket.  When we saw that it was, in fact, a simple operation, and that the impeller was in good condition, we should have suspected that fate was just teasing us.





Pre-filter before cleaning, the contents, and the cleaned canister.
Bolstered by this initial success, we moved on to the pre-filter and water separater.  By turning a small valve at the bottom of the filter canister, you can bleed out a sample of the fuel.  Ours looked like Turkish coffee.  Guru Bob explained that it wasn’t supposed to look like Turkish coffee.  We took the filter apart and, not surprisingly, it looked like the bottom of a Turkish coffee pot.  The liquid drained from the canister, however, took on the allure of a nice Black-and-Tan mixed beer, with the water and dark matter in the bottom and the diesel floating on top.  Cleaning it out and replacing the filter was a relatively straightforward affair, but of course, this was a sign that there was trouble brewing further along the line.   

The filter, before and after.
Next, we decided that we should check out the fuel filter.  Not surprisingly, it looked like a Turkish coffee pot, too.  And once more, cleaning out the filter canister and replacing the filter was easy*, but this was just a symptom of bigger problems yet to be resolved.
(* “easy” is a relative term meaning that it is conceptually simple.  However, even the simplest task on a boat motor is a royal pain in the butt because space is limited and access to the part you want to work on is always blocked by at least two other things.) 


Tank goobers.
Examining the root of the problem could no longer be avoided, and we decided to inspect the tank directly by removing the fuel gauge sensor and peering into its fitting hole.  The good news is that there was no rust.  But there were numerous black gelatinous goobers floating in the fuel and clinging to the bottom, indicating a bacterial bloom.  

 The solution: 
  • Drain the tank.  (Guru Bob had a kick-ass electrical drill-driven pump)
  • Remove the tank from the locker.  (Dehler calculated this to the ½ milimeter and it was not easy to get it in or out of the locker…lost a little gelcoat around the rims.)
  • Clean it with a hot water high-pressure hose.  (That part was fun.)
  • Rinse it with gasoline and let it dry.  
  • Put it back into the locker and reconnect all the lines.
  • Filter the diesel and treat it with an anti-bacterial additive.
  • Put the cleaned diesel back in the tank, and
  • Prime the system to get the air out.
Tank operations.

This all took two days.  The shipyard mechanic came to help us prime the system once we had got everything put back together.  There is a small hand pump on the motor between the pre-filter and the filter.  You remove a screw to open up a hole on the top of the filter to let the air escape while you pump.  We’re glad the mechanic was there, because it took a helluva long time to prime and we would have given up thinking we were doing something wrong.  But we eventually got the big belch and the fuel ran clear.

Motor running smoothly ... with no leaks !
The mechanic then turned to us and said, “I think it would be a good idea if we fired up the motor to make sure everything is running smoothly before you put it in the water.”  YES !!  We weren’t sure how to manage this ourselves and having him there to help was a great relief.  We rerouted the water intake to a bucket that we filled continuously with a hose, and with little effort, the motor started right up … and NO LEAKS !!  What a great compensation for 2 full days of really dirty work ! 

While the mechanic was still with us, Patrick brought up a recent story we’d read in the newspaper about a sailboat who’s engine began revving out of control, overheated, burned and sank the boat in a matter of minutes.  The captain had shut off the diesel to the motor, but that had no effect.  The mechanic explained that this can happen when the oil is too full, and that the only thing to do in that case is to smother the engine by blocking the air intake.  He showed us how to do this by opening up the canister of the air filter and placing a rag in the intake pipe.  But when he did this, we discovered that there was no air filter.  The wire basket that holds the filter was there, but the thin foam filter was missing.  That one truly was easy to fix, but very expensive for such a flimsy little thing.

I’m sure that the care and feeding of the marine diesel motor still holds many mysteries for us, but we certainly feel more confident after our 2 day crash course and we know that everything is now in good working order.  With only 5 days left on land (in theory) it’s great to get this out of the way.   

Posted on Sunday, August 12, 2012 | Categories:

Tuesday, 7 August 2012

Propeller Shaft Tube: The Final Chapter


It sounded so simple.  “Now that I’ve changed the propeller shaft tube and re-stratified the hull, all you guys have to do is check the alignment with the gear box, tighten all the screws and change the rubber stuffing box.”  The friend-of-a-friend who helped us with the propeller shaft tube drama left us with these cheery words of encouragement.  But we knew better (at least I did; as I’ve mentioned before, Patrick is hopelessly optimistic*).   
(*optimistic and lucky !  See Addendum to Tubed)

Of course, the shaft was not perfectly aligned with the gear box, and if the tube is already stratified in place and thus not moveable, the only other solution is to move the motor.  When the mechanic told us this, I thought it was a joke and let out a hardy belly-laugh to play along, which was promptly met with blanks stares. 

I was envisaging a huge crane with chains and winches to lift the motor off the chassis to reposition it.  In fact, all that was really needed was a small fine-tuning of the position, which is accomplished by adjusting 4 x 4 sets of screws on the engine mounts (silent blocks).  We were also told that a crow bar might be handy.  Not having a crow bar, we can report that the center support from an old beechwood IKEA table works well, too.    

The 2 "easy-to-reach" engine mounts (red circles).
Guru Bob came over to help with this task, which involved painstakingly loosening and tightening sets of screws that were both rusted and, for 2 out of 4, nearly impossible to reach.  After more than 3 hours of tweeking and several good shoves with the IKEA lever, we got something that looked pretty good.

The mechanic came over to inspect it the next morning and confirmed that it was pretty good.  But not good enough.  We were reduced to measuring the gap differences between the gear box and the intruding propeller shaft with one of those little red straws that comes with a can of WD-40.  With this fine gauged instrument, we could see that indeed there was more space on the top than the bottom.  Back to tweeking.

Patrick and I tackled it alone this time, which meant that after 2 hours of going around in circles (it's better, it's worse, it's better, it's worse), I threw down my WD-40 straw and said, “This is madness !  Let’s just PAY SOMEBODY to do this !  We’re never going to get it aligned !” to which my better half suggested that I take a little break and go work on something else.  Another hour later, he called me to come check his work, and it was nearly perfect.  We spent another few minutes fine tuning the fine tuning and decided that it just wasn’t going to get any better.  The next day, the mechanic verified our work and this time said “Not bad at all !”

Greasing the rubber stuffing box (Volvo Joint).
Patrick asked how long it takes a pro to do one of these alignments.  Our mechanic said it typically takes about 3 hours if all goes well, but he said he has taken up to 2 full days to get it right sometimes.  He gave us the green light and we tightened all the screws and connected the new rubber stuffing box.  We had anticipated having to call in for help on that task since it’s a rather important piece (the thing that keeps water from gushing into your boat through the shaft tube).  But at that point, we were so battle-worn that we just decided to do the damn thing ourselves.  We had instructions (with pictures !) and the mechanic talked us through it before hand.

And now it’s done.  The whole 2.5 month drama is finished. 

Gear box, shaft, and suffing box fixed to shaft tube: before and after.

And strangely, we don’t really feel like celebrating.  As the resident pessimist, I am waiting for the proverbial other shoe to drop, with an ever-present voice in my head saying “we’ll see, we’ll see…it’s not over yet”.  Even Patrick isn’t rushing to pop the champagne cork.  It’s hard to feel victorious when we’ve got so many other jobs ahead of us and summer is wasting away (if you dare to call 6 days without rain in 2 months “summer”).  But never fear, a big bubbly gin and tonic will mark a healthy and well-deserved pause and we’ll celebrate when we’re on the water enjoying the fruits of our labour.
Posted on Tuesday, August 07, 2012 | Categories:

Thursday, 2 August 2012

The Life Raft Conundrum


If you intend to navigate more than 6 nautical miles from shore, French regulations stipulate that you must have a life raft on board.  These rafts come compressed in containers the size of a largish suitcase and are inflated automatically by a pressurized CO2 system that is tripped by pulling a sort of rip-cord.  The rafts come in several sizes depending on the number of people on board and are equipped with emergency tools and supplies for either 1) a rescue probable within 24 hours or 2) a rescue with a wait of longer than 24 hours.  

Ours is a < 24 hour model but augmented with a grab bag containing all the items found in the > 24 hour version plus other items we don’t want to be without while bobbing around waiting for a lift. 

Life raft in container; grab bag; and deployed life raft.

The basics to add for > 24 hours are a set of emergency flares, thermal protective blankets, a first aid kit, 1 liter of water per person, and 500 grams of food rations per person.  To this, we will also add a portable VHF radio, an EPIRB (GPS emergency position-indicating radio beacon), a bailing bucket and sponges, glow sticks, a water-tight flash light, a small compass and navigation ruler, a fog horn, a sac of batteries (for flash light and radio), a fishing line, 2 baseball hats and sun screen, and photocopies of all our important papers.

And after having read the survival manual stored inside one-such life raft, you can bet that I won’t be abandoning ship without my red lipstick and pantyhose.  Now, the official story is that the lip stick is useful for writing a brief message on the limp body of your companion to signal to your rescuers exactly what is wrong with him / her in the case that he / she is air-lifted out of the raft before you.  The pantyhose, we’re told, are useful for straining the water to capture plankton for a light snack.  Frankly, I’m not buying it.  I think these two items have been suggested in a sorely misguided attempt to provide (uh-hum) “entertainment” during a possibly long wait.  (Well yes, in fact, it was a French survival manual, now that you mention it…).

So far, so good.  But the conundrum is where to store your life raft.  If you’re lucky, you boat has been designed with the life raft in mind and has its own dedicated storage space under the helmsman’s seat or in a special compartment on the transom.  Unfortunately, this is quite rare, especially on older boats, and alternatives must be found.

Of the 23 different boats we’ve sailed on, the majority simply store their life raft in the bottom of the cockpit locker.  This is a fine place for it.  It’s out of the way and in a protected location.  The only problem with this is that it is highly improbable that you will ever be able to get it out of the locker if you ever need it in a hurry (and when would you ever need it not in a hurry?).  These suckers weigh about 35 kilos (~75 pounds), and most cockpit lockers are deep, meaning that you have to get down on your knees and lean over waist-deep to even get your hands on it (after, that is, removing the bucket, the hawsers, the water hose, and the spinnaker sack that will inevitably be stored on top of it). Did I mention the saloon is on fire and you’re taking on water in a storm?

Some forward thinkers have hooked up their rafts to a pulley system that will allow them to hook one end to the boom and then hoist the raft out of the cockpit locker with the pulleys, but if you’re in an abandon-ship situation, you may not be able hook up such a system in a rush, especially if you’ve lost the mast or can’t control the boom.

The rule of thumb is that the weakest member of the crew should be able to launch the raft with one arm (the other being broken, of course).  The above-mentioned situation, even with a pulley system, won’t work for either of us.

A good method is to fix the raft to the railing of the balcony above the transom with a stainless steel support.  But your boat has to have a sufficiently strong and wide balcony to bear this weight on a rolling ship, and if you have a relatively light boat like ours (a svelte 4.5 tonnes) you have to think about balancing out all the major weights in the boat, such as the fuel tank, the water tank, etc.  Our balcony just doesn’t look strong enough or wide enough for this, and it would have to be placed on the same side as the water tank.

Our remaining option is to fix the life raft to the coach roof, in front of the companionway and behind the mast.  Here, the weight of the raft is centered and it is high relative to the surrounding deck, so it can be pushed, rather than lifted, into the water.  The drawbacks are that the coach roof was never designed to take this kind of load and depending on the boat and/or the life raft, its placement here can limit visibility forward and interfere with the boom downhaul.

Raft tied to coachroof.
When we did our test sail on Zephyr, Antoine and Caroline had the life raft rigged this way, sitting flat on a no-skid mat and wrapped up snugly with an impressive web of 20 meters of strapping.  They said it never budged during their entire trans-Atlantic voyage, despite some rough weather.  In this configuration, a good sharp knife is kept handy in the companionway to cut away the lines in a hurry.  Fortunately, the visibility forward wasn’t affected and it was low enough that it didn’t touch the boom downhaul.



Patrick and I decided that we would keep the raft on the coach roof, but that we would get fancy and buy a stainless steel support that is screwed or bolted to the deck.  The advantages are that the support offers a quick-release system and comes with a lock (since, sadly, life rafts have been known to disappear if left unlocked on the deck). 

Our raft with quick-release straps.
But after reading up on life raft positioning in the sailing forums, I had a change of heart.  Stories abound of waves and knock-downs ripping the support from the coach roof, leaving holes where the support screws used to be.  As a general rule, I don’t like putting holes, even small ones, in the boat if not absolutely necessary, so these stories sent a shiver up my spine.  On a more practical note, when we saw the system at the ship chandler’s, we noticed that the stainless steel tubes were 3 cm high.  That small 3 cm was just enough for our raft to touch the boom downhaul, and we could imagine it getting snagged each time we tacked. 

So we decided that the system of Antoine and Caroline was perfectly well-adapted to the situation after all and that we would simply use individual quick-release straps rather than a single 20 m line to fix the raft to the deck. 


We’re still trying to figure out how to add a lock system to this configuration.  A word of advice to would-be boat buyers: look carefully at the life raft placement possibilities.  This shouldn’t be an afterthought.  And don’t forget the emergency lipstick and pantyhose, either.
Posted on Thursday, August 02, 2012 | Categories:

Wednesday, 25 July 2012

A Hodge Podge of Bricolage

We have a victory to report.  If you’d told us a few months ago that we would dismantle the steering quadrant, replace the ball joint / rotator pin, and adjust the steering cable tension by ourselves, Patrick would have laughed and I would have broken down in sobs.  As it is, we’re just smugly pleased with ourselves.  (See Rainy Afternoons and Rudder Angles for the background.) 

The hopelessly stuck ball joint / rotator pin.
But the task didn’t start out so well, and if you know anything about this kind of job, you’re asking yourself, “Now why the heck did they take apart the steering quadrant just to change the ball joint?”  Because it was stuck, that’s why.  Irredeemably stuck.  So stuck that we called in the mechanic to see if we were doing something wrong.  After he tried forcing it off with a couple of screwdrivers, he told us to take apart the whole steering quadrant and bring the offending section into the shop.  There, he proceeded to attack it with a blow torch and what I think is called a hub grappler (in French, arrache-moyeux) and what I know is called a really big hammer.  

Half the steering quandrant with new joint and clean bolts.
Once the joint was replaced and all the parts were cleaned with turpentine and re-greased, putting it back together was pretty simple (although it helps to be a fan of the game Twister).

The shiny new ball joint in place.
We adjusted the tension using the screw pin connecting the steering column to the rotator pin.  By adjusting the screw pin a few turns at a time, we managed to get rid of about 2/3rds of the play in the wheel, and when we manually put the rudder straight, the wheel lined up with what we assume is the original (red) mark indicating a straight rudder.  Not too shabby.
 
We’ll keep fine-tuning to see if we can get rid of the rest of the play in the wheel, keeping in mind that “Great is the enemy of Good”.











I’ve also had a splicing fit recently:  spliced the rode to the anchor chain and made an eye splice on the other end of the rode to connect to the boat.

Chain splice and eye splice.

We installed two battery controllers (we actually only did the physical placement of them on the nav station… the electrician will come and hook them up to the batteries later).

Battery controllers installed.

And we finally tracked down a new control panel for the motor controls.

Motor control panel: before and after.

Despite this wave of activity, we’re really no closer to getting Spray into the water.  The boat yard announced that they had a backload of work and summer vacation has shut down many of their suppliers; in particular, the one who is supposed to give us an aluminium plate to reinforce the chain locker where the windlass will be placed.  We’ve got at least another 2 weeks on land.
Posted on Wednesday, July 25, 2012 | Categories:

Tuesday, 24 July 2012

Tubed !

In what the statistics confirm has been the rainiest June / July since 1959, we FINALLY had a weekend with no rain and a friend of the former owner came to help us install a new propeller shaft tube.  (Confession: he did the work and we fed him sandwiches and beer.)  It looks great and the polyester tube is more marine-friendly than the stainless steel mix that was rusted and pitted.  If you're wondering why we changed the tube, see The Naked Truth Parts I and II.

Prop shaft tube: before and after.
Of course, if everything went smoothly, this would all cease to be fun, right?  Luckily for us, there are a couple of glitches to keep things interesting.  When he took the rubber stuffing box (in French “joint Volvo”) off the shaft, he saw that it was quite worn and suggested that we change it.  He didn’t have a spare one with him so we now have to scout around to find one (early attempts this morning suggest this will not be so straightforward, either).  He also had to cut away the rusted bolts on the gear box to liberate the shaft, and didn’t have spare bolts of the right size to replace them. 

Needed: bolts for gearbox (left) and a volvo joint (right).
Once we have located all the missing parts, we can put everything together and write a big DONE next to this job in the maintenance log.  But neither of us feels confident enough to install the Volvo joint ourselves since this is a critical element that keeps water from gushing into the boat through the propeller shaft tube.  The instructions sound simple enough but we’ve never seen it done before, so we’ll call in reinforcements for this one.

We also learned a valuable lesson, one which you may very well find bleeding obvious, but as the saying goes, “one experiment is worth a thousand expert opinions.”  When you take a circular saw to the hull of a boat, fine dust goes everywhere.  We had been warned and put plastic covering in the work area.  This is useful for catching about 50% of what flies, and the rest you just have to vacuum up afterwards.  Here’s what we learned:  a vacuum cleaner intended for regular home use just isn’t up to this kind of task.  After about 45 minutes of vacuuming with my hot pink Electrolux home-edition, it began making an angry, high-pitched whine, became very hot, and gave up the ghost with a big dusty belch.

So before making the rounds of the ship chandler’s to look for missing parts, we went to the hardware store and bought a manly man’s wet-dry shop vac for the boat (it’s yellow and black) and took my little pink machine to be repaired.  Now, we may have our dim moments, but we knew that we shouldn’t admit that we were using it to suck up polyester resin fiberglass boat hull dust.  In the parking lot of the repair shop, we prepared our story.  We would simply tell them that it was plaster dust from a small home repair job. 

“Plaster dust ?!  It says clearly in your instructions that the machine isn’t to be used with ash or fine dust. I’m afraid your warranty won’t cover this.”  At that moment, my American instincts kicked in and I began planning how I could fight them on this by pointing out that their instructions said nothing about polyester resin fiberglass boat hull dust.  But while I was scheming, I also heard something in the background that sounded like “…it will cost more to repair than to buy a new one” and saw the flash of defeat and resignation already on Patrick’s face.

My hot pink electrolux (R.I.P.) and the new shop vac.
Reviewing the day’s events over beer later in the evening, my assessment was that the day had been a rather poopey one.  Patrick, a born optimist, just announced with a smile, “we’re less stupid now than when we woke up this morning.” 

Addendum:  A few days after this post, Patrick took our little pink Electrolux back to the appliance store to ask them how to get into the motor compartment so he could try cleaning it himself.  A different guy was at the help desk and suggested sending it to the shop and asking them for an estimate of how much it would cost to clean and repair.  A couple of days later, we get a call to come and pick it up.  Twenty-eight euros, thoroughly cleaned and with a new filter.  What do you get when you combine a ruthlessly positive attitude with tenacity and luck?  Patrick, that’s what !  Drives me banoonoos sometimes, but gotta love him !
Posted on Tuesday, July 24, 2012 | Categories:

Thursday, 19 July 2012

Rainy Afternoons and Rudder Angles

Here is a tale about how a simple mathematical musing can uncover daunting new tasks requiring skills you don’t have to fix a problem you never suspected.

It all started rather innocently, as these things always do, when I was looking for things to do on the boat while waiting for the rain to stop.  I remembered that one of my books on sail trim suggested calculating the rudder angle while the boat was in dry dock, and this sounded like a great rainy-day activity.  As we say back home, “you may as well dance when it’s too wet to plough.”  Now admittedly, it is difficult to liken rudder angle calculations to dancing even by the most enthusiastic math nerd, but I was happy to find something that felt like a useful task on such a dreary day.  And, truth be told, it sounded like fun.

When you are under sail, you set and trim the sails according to the wind direction and the direction you want to go.  On a well-trimmed and well-balanced boat, the rudder stays more or less straight, in line with the boat.  Joshua Slocum’s Spray was a boat that was so well-balanced that he could simply tie a rope to the tiller to keep it centered and let her go for days at a time without adjustments (in steady winds, of course).  This was quite a feat in the days before auto-pilots, and was a major factor contributing to his successful solo-circumnavigation of the globe. 

When it is necessary to hold the rudder at an angle to maintain your bearing, it means that your sails are not well-trimmed.  Beyond a certain angle, the flow of the water against an angled rudder turns your rudder into a brake.  This is bad, and depending on the expert you consult, occurs between 6° and 9°.

Most boat steering wheels will have the center point marked so that you know when the rudder is straight.  Now the trick is to mark the point corresponding to 6° of rudder angle on either side the center mark to know when you are braking and need to re-trim the sails. 

If the rudder could turn 360°, the radius of that circle is the distance from the central pivot point (the rudder stock) to the trailing edge of the rudder.  On Spray, this distance is 37 cm.  Of course everyone remembers that the circumference of a circle is calculated using the equation:  c = 2 Ï€ r    (confession: I googled it.)  At MIT, where the sports teams were rarely the school’s strongest point, there was a cheer to amuse the crowd: “Cosine! Secant! Tangent! Sine! 3 point 1 4 1 5 9 ! ” so it’s easy for me to remember the value of Ï€.  For my rudder with a radius (r) of 37 cm, this gives a circumference of 232 cm for 360°, and by a simple ratio calculation, the 6° of rudder angle I seek is located 3.9 cm from the center position.

With numbers in hand, we moved to the practical-application step.  With Patrick up top at the wheel and me beneath the rudder (no dummy, me… he got rained on while I was protected underneath the boat), I measured off 3.9 cm on either side of the center point and had him slowly turn the wheel until the rudder was lined up with my marks.  We did this a couple of times in each direction and he marked the 6° points on the wheel with a marker. 

“How’s it look?” I shouted up to Patrick.  The response was the worrisome French expression “Ooh laaa…”.  This is not to be confused with better known “Ooh la la” which is generally a happy expression of appreciation.  “Ooh laaa” is most appropriately translated as “uh oh” or, in certain cases such as this, “oh shit”.

I climbed up on deck and looked at the two marks on the wheel.  They were not symmetric from the center.  By a long shot.  One was a full 10 cm further away from the center than the other.  “Ooh laaa” indeed.  This was a clear indication of something we knew already but had not fully appreciated:  there was considerable play in the wheel.  When we took the boat out for a test sail, we noticed that there was some play, but it didn’t seem particularly bothersome.  Clearly, after lifting the boat out of the water a second time and 2 months in dry dock with various assaults inflicted on the rudder, the play had increased significantly. 

Back at home, I looked up how to stiffen up a limp steering wheel.  The forums all suggested it was something that could be done easily, but this sort of statement always leaves me a bit queasy.  The next day on the boat, we took advantage of a brief visit from the head mechanic to ask him what he thought about the situation.  He spun the wheel slowly, watching the quadrant rotate from side to side and pointed out that most of the play seemed to be coming from the rotator pin connecting the quadrant to the steering chains (rotule, in French; see photo).


The rotator pin connected to the steering quadrant.
This reminded me that Antoine, the boat’s previous owner, had left us a spare rotator pin in case we needed to change it.  The mechanic assured us that it was a simple affair to remove the old one and attach the new one.  When he had gone, Patrick, emboldened, started looking more closely at the situation and rapidly ran up against the first hurdle:  he didn’t have the right size of wrenches. 






As with so many things that we attempt to do on the boat, my simple “mark 6° of rudder angle on the wheel” has now become:
  •  Buy new set of wrenches.
  • Mark the current position of the rotator pin and bolts.
  • Remove the damaged rotator pin and install the new one.
  • Test the play in the wheel; if acceptable, proceed to next step; if not, turn the bolt on the connecting pin by 2 turns to tighten the chains; repeat as necessary
  • …and then, mark 6° of rudder angle on the wheel.

Monday, 9 July 2012

Bricolage Update


In honor of the upcoming 14th of July French National Holiday, I would like to take this opportunity to pay homage to the French language for giving us the word “bricolage”.  In English, this is translated as “Do it Yourself” but I have to say I find this phrase rather inadequate to describe what actually happens when you repair, install, or build things. And bricolage can be turned into the verb “bricoler” (breek-o-lay) to describe the act of doing the work, while telling someone that you are “DIY-ing” just doesn’t have the same elegance. 

So here is a bricolage update with our recent successes, mixed-successes, and set-backs.

Our non-standard flexible faucet tubes.
Repaired galley sink leaks.  We thought all we would have to do is to block off the hot water intake line.  There’s no hot water, but the faucet mixer opens the hot water intake line and allows cold water to flow out … all over the floor.  But the flexible tubes for the hot and cold water are not standard sizes for Europe.  After 3 visits to various plumbing stores, one very nice man led us to a back room and ripped the tubes off an old sink they had sitting around.  He just gave them to us... said he couldn't sell them because they weren't standard.  Perfect fit.  Another fitting that was in bad shape was nowhere to be found in the hardware stores.  We finally found something that did the trick in our local garden center. 

Passed electrical cables for windlass.  We found out that we didn’t need to buy a new battery for the windlass after all (see post “The Learning Curve Blues”) but can instead use the service batteries (2 x 100 Ah batteries in parallel) which are even closer and easier to reach for the cabling. Passed electrical cables from the chain locker to the battery and from the chain locker to the cockpit locker for a control button near the throttle.

New cables installed (looking down).
Installed new electrical cables between the service park batteries.  Found out that the cables connecting the two service park batteries are not sufficient for a big electrical draw (such as needed for a windlass) to pass between the two.  Bought new cable, ripped out the old, passed the new under the floorboards.  



GPS antenna installed.

Installed new GPS antenna.  More cables passed, from the chart table controls to the locker behind the head where we installed the antenna to keep it out of harm’s way.  Gets kick-ass reception there, too.

Repaired two hatches that had minor leaks.  We noticed some small leaks around two hatch covers, and when we unscrewed the covers, we noticed that there were wads of paper towels strategically placed to catch any drips. We decided to replace the paper towels with spray foam insulation. The insulation expands and forms a lovely effect like snow sliding off a roof, which then hardens, allowing you to cut it to the form you need.  

Foam insulation around hatch cover.
New super-hold hair mousse discovery.
Unfortunately, one of the globs became so heavy that it started falling towards the floor.  I raced to catch it with a paper towel.  Turning around proudly to show Patrick my catch, he says “Ohhhh noooo… your HAIR !”  What about my hair?   


A quick look in the mirror showed a big blob of insulation across my forehead.  My attempts to remove this “cotton candy super glue” with towels and acetone only met with limited success and the residue turned rapidly to hard plastic. 

Collateral damage, hatch job.
Back at home, after repeated failures with various oils and solvents, I was reduced to pulling hair out of the plastic globs strand-by-strand.  Most just broke off, and I had to use a razor blade to separate the worst of the lot.  It took a ½ bottle of white wine to deaden the pain after all the hair pulling.






It'll fade, right?
Repaired dings in gel coat.  We learned that with an electrical sander, you get a nice smooth finish after patching dings in the gel coat.  The problem is that I didn’t have the right color of blue gel coat, so I used white, with the idea of painting it afterwards.  But I didn’t have the right color of paint either, so I mixed two blues to get something close.  After reading the forums on this, I’m told that all of this will peel and crack in a very short time anyway, so I’ve decided not to stress over the bad color match.  Sigh.


Eye splice + needle-and-palm whipping on devil's claw.
Made eye splice for devil’s claw.  Bought a sort of devil’s claw, which is used to reduce the strain on the windlass by hooking into one of the links and transfering the strain to a cleat on deck.  But you have to attach the metal claw to a polyamide / nylon line by making an eye-splice and wrapping any loose ends with needle-and-palm whippings.  After a few false starts, my Seamanship 101 and 102 classes from Texas A&M came flooding back to me and it turned out okay.  (Don’t look too close, though).   



Set up / programmed the new portable VHF radio.

Replaced the lock on the companionway door.  It’s a good fit, but we still need to “bricoler” something to eliminate a gap.

Set up new computer.  The problem is that the graphics card for this operating system has been known to have big problems with the navigation software we wanted to use.  We’ll test this using a friend’s software before buying it ourselves.  But we have to wait for that friend to get back from sailing in the Caribbean.

Twiddled thumbs over propeller shaft work.  The work on the propeller shaft is a major setback.  The friend-of-a-friend who has agreed to help us can only help us on the weekends when it doesn’t rain. It was just announced that this June was the rainiest June since 1959, and July doesn’t look much better.  We wondered if maybe the boatyard would be able to work faster, since they would be able to work any day it didn’t rain.  We asked what their workload was like at the moment, and they announced that the guy who was scheduled to work in July and August has just run off to Mexico with his girlfriend and did not say anything about coming back.  This will also push back the work on the chain locker needed before we can install the windlass. Sigh.  Back to square one.
Posted on Monday, July 09, 2012 | Categories:

Monday, 2 July 2012

Hull Work


The next few posts will show the gradual transformations of different parts of Spray’s anatomy that have occurred over the last couple of weeks. 

Today’s feature: The Hull.

The hull was water/sand blasted to remove what was left of 20 years of bottom paint. 
Bare, with rust spots already starting on the iron keel.















The iron keel was treated with 4 layers of epoxy (AC20, red). 

Red epoxy on the keel.















An epoxy primer was put on the hull, followed by application of a mastic epoxy putty (enduit) where needed to fill in any pits.  Silicone mastic was put around all the through-hulls, and 2 layers of epoxy undercoat finished off the prep work (SC20 epoxy undercoat, light tan).

Epoxy undercoat on the hull.















The keel, before and after scrape, epoxy, and new seal.











Finally, a coat of new bottom paint (dark blue) was added.  We had to do this in 2 steps; paint around the supports, have the boatyard move the supports, then paint over the spots.   

Blue with tan spots.















1st layer of bottom paint DONE.
The 2nd will be added a few days before Spray goes in the water.  

We used a hard matrix bottom paint for this first layer, but in coming years, we will switch to erodible matrix. 

In fact, we were just informed yesterday that it will be increasingly difficult to put any bottom paint on the boat in the coming years because of environmental issues and the need to have specially-equipped boatyards to perform the work.   

Many sailors are now moving to the Oceo-Protect system, which is supposed to last anywhere from 5-10 years.  But like Scarlett O’Hara in Gone with the Wind, “I’ll think about that tomorrow”.          
Posted on Monday, July 02, 2012 | Categories: