Friday, 24 August 2012

Afloat !



Spray was launched this morning at 11 am and is resting comfortably (we hope) on her mooring in the Auray River.  Everything went smoothly, despite scattered showers and a stiff breeze.

Spray hanging from her ball in the Auray River.
We now believe what we have been told: if you wait until everything is perfect to put the boat in the water, you’ll never put the boat in the water.  At least our remaining problems are not ones that require the boat to be on dry land.  

Since the last update, our gremlins continue to play hide-and-seek.  Two days ago as we were putting on the last coat of bottom paint, we noticed that the joint around the keel was still sticky and gooey.  After 2 months of drying time, we thought this a bit odd and called the boatyard guys to check it out.  They declared that the sealant had failed to cure, which, according to the Sika company, is a “phenomena” that happens in about 1 in 10 batches.  (Now honestly, is a known, regular 10% frequency really a phenomenon?)  That was easy enough to fix but fortunately we had already postponed the launch date.

Our last big mystery is the alternator failing to charge the batteries.  The electrician said he’d never seen anything like it, and suspects the regulator.  We have a date next Wednesday with the experts in Crouesty, the largest port in the Gulf of Morbihan area.  Fortunately, it’s something that can be fixed with the boat in the water, so no excuse for a launch delay.

3 burners with 30mbar pressure regulator.


The gas stove now works with our new French fittings.  We had anticipated not being able to use all 3 burners at the same time, since the new pressure regulator is 30mbar and the original German one was 50mbar, but when we fired up the burners, we got a good strong flame out of all 3.  Crazy Germans.  (wink at MV !)





The bow plate has been installed (zoom in on 1st photo above) and we added an anchor-chain connector (Junction KONG) so that the chain and anchor retract smoothly in the bow roller.  Because the hole in the anchor stock was not a simple round hole but an oblong one, the junction tended to slide down when not under strain, so we had to fill the hole with some clever seamanship.  Time will tell if it holds up to chaffing, but it works well for now.

Anchor-chain connector.
We finally removed the last 2 names of the boat from the transom (Zephyr and Er Gwennick) and put the SPRAY sticker in place.  We opted for a metallic silver color that we thought would be evocative of sea spray shining in the sun, and unfortunately this is the case, rendering it a bit hard to see when the sun hits it at a certain angle.  We also renamed the life buoy but I suspect Zephyr is still written on the inflatable annexe.  A battle for another day.

SPRAY !
And for our next trick, 3 days of REST !  We’ve been working very long days non-stop for the last 3 months and my body’s alternator, like Spray’s, has entirely failed to recharge my batteries. 

A big thanks to all who gave advice, equipment, and a helping hand in getting Spray into the water over the last 3 months:  Antoine and Caroline, Remi, Daniel, Roland, the Le Borgne Crew (Nicolas, Patrick, Yves, Alain, Eric, Betty, et Helene), the E3 electricians Patrick and Philippe, Jacques (we tested out the annexe this morning - it's perfect - thank you !), and last but foremost, Guru Bob.

Posted on Friday, August 24, 2012 | Categories:

Saturday, 18 August 2012

Launch Scuttled by Euro-Gremlins


Mark my words: Europe is doomed.  Forget harmonization of social security, retirement, and the minimum wage.  The problems run much deeper, like the fact that German screw threads turn to the right, and French screw threads turn to the left.  I haven’t had the time to investigate further, but at first glance, it appears that most of the Anglo-Saxon EU countries follow Germany’s lead, while the Latin “Club Med” countries stick with France.  I’m sure a closer investigation would reveal pocket alliances resembling the voting in the Eurovision Song Contest  (For non-European friends unfamiliar with Eurovision, it’s uncomfortably like the Gong Show without the gong.)

We discovered this charming example of regional diversity whilst trying to re-plumb our cooking gas lines.  The original fittings were so rusted that it was hard to tell where one nut ended and the next one began, and so we decided to change them all.  A word to the wise who find themselves in a similar situation:  DON’T.  Rust is also known as “the poor man’s Loctite” and that original rusty system probably had less chance of leaking than the new one we planned to install. 

The connection to the copper tubing was still good and we had hoped to use the same pressure regulator.  Long story short:  After 7 visits to different hardware, plumbing, boating and camping stores, the answer was nyet.  The hoses and fittings we buy in France cannot be made to work with the original German fittings.  We have now a shiny new French system, where the next challenge is to make this French system fit in the gas tank compartment of the German boat.  This will involve drilling a new hole in the compartment and bending / aligning the copper tubing that runs to the stove. 

Yoga helps, too.
The next bugaboo was the electrical system.  I realized that working with gas and electricity made me nostalgic for those sweet simple days of working on the engine.  Engines are fairly straightforward beasts, and there are lots of technical books to help you.  Every country, nay, every boat owner, seems to want to put his personal stamp on the electrical and gas systems, and there is no way to know what they’ve done or why … just a mass of multi-colored spaghetti with strands trailing off behind bulkheads, never to be seen again.  We have the original German wiring diagram, but after 20 years in the hands of 2 different French owners, there is little resemblance.  To keep things really fun, nothing has been labelled. 

After a nervous hour of trying to figure out why the service batteries were no longer feeding any of the instruments, we discovered that the system is outfitted with a fuse that had blown.  How or when it had blown is still a mystery, but at least the problem was easy to resolve.  We debated putting in a breaker switch instead of using fuses, but the smallest breaker available was 60 amps, which we thought was probably too high to give much protection.  Next, we realized that the 220V recharging system was wired to the control panel rather than directly to the battery, meaning that the batteries would only be recharged if the circuit breakers were closed.  Why?  Fixed that. 

The major problem du jour is that the alternator is not charging the batteries.  The alternator works fine and the recharger works fine, and when wired together correctly, the system works fine.  But the system is not wired correctly and none of the motor controls function except the ignition alarm.  The electrician we worked with yesterday gave up at 8 p.m., apologetically announced that he had to go on vacation, and gave us the telephone number of a colleague who might be able to help us.    

The original launch date was based on finalizing our major refits, namely the propeller shaft tube and the windlass, both of which are now done.

Reinforcing and stratifying the forward part of the chain locker.
Windlass and foot controls in place, chain marked every 5 meters.

However, our lesser tasks, by their number (33) and “regional diversity issues”, have now become a force to be reckoned with, and the launch has been postponed for one week.  Looking over my list, I’m wondering how many more Gremlins are lurking.
Posted on Saturday, August 18, 2012 | Categories:

Sunday, 12 August 2012

Diesel Motor Crash Course


If you are growing weary of all our technical dramas starting out with “it all started out so simply”, then just imagine our frustration.  This one really did come out of nowhere, or to be more precise, from the cautionary tales of a fellow mariner who had a nasty surprise during his recent summer sailing trip.

Guru Bob, recently returned from the aforementioned trip, suggested that we check the pre-filter of our diesel engine to look for any rust particles that may be emanating from our 20-year-old “stainless steel” fuel tank that just might clog up a fuel line when you least expect it.  Since the fuel is of dubious origin (the Caribbean) and had been sitting in plastic jerry cans for over a year before being put in the tank, he also suggested we check for condensation.

Water pump impeller and gasket.
The engine has always been an element of moderate anxiety for us, and we were eager to get to know it a bit better before trusting it blindly in potentially dangerous situations.  Before tackling the fuel lines, we decided to start with something simple: checking the water pump impeller and gasket.  When we saw that it was, in fact, a simple operation, and that the impeller was in good condition, we should have suspected that fate was just teasing us.





Pre-filter before cleaning, the contents, and the cleaned canister.
Bolstered by this initial success, we moved on to the pre-filter and water separater.  By turning a small valve at the bottom of the filter canister, you can bleed out a sample of the fuel.  Ours looked like Turkish coffee.  Guru Bob explained that it wasn’t supposed to look like Turkish coffee.  We took the filter apart and, not surprisingly, it looked like the bottom of a Turkish coffee pot.  The liquid drained from the canister, however, took on the allure of a nice Black-and-Tan mixed beer, with the water and dark matter in the bottom and the diesel floating on top.  Cleaning it out and replacing the filter was a relatively straightforward affair, but of course, this was a sign that there was trouble brewing further along the line.   

The filter, before and after.
Next, we decided that we should check out the fuel filter.  Not surprisingly, it looked like a Turkish coffee pot, too.  And once more, cleaning out the filter canister and replacing the filter was easy*, but this was just a symptom of bigger problems yet to be resolved.
(* “easy” is a relative term meaning that it is conceptually simple.  However, even the simplest task on a boat motor is a royal pain in the butt because space is limited and access to the part you want to work on is always blocked by at least two other things.) 


Tank goobers.
Examining the root of the problem could no longer be avoided, and we decided to inspect the tank directly by removing the fuel gauge sensor and peering into its fitting hole.  The good news is that there was no rust.  But there were numerous black gelatinous goobers floating in the fuel and clinging to the bottom, indicating a bacterial bloom.  

 The solution: 
  • Drain the tank.  (Guru Bob had a kick-ass electrical drill-driven pump)
  • Remove the tank from the locker.  (Dehler calculated this to the ½ milimeter and it was not easy to get it in or out of the locker…lost a little gelcoat around the rims.)
  • Clean it with a hot water high-pressure hose.  (That part was fun.)
  • Rinse it with gasoline and let it dry.  
  • Put it back into the locker and reconnect all the lines.
  • Filter the diesel and treat it with an anti-bacterial additive.
  • Put the cleaned diesel back in the tank, and
  • Prime the system to get the air out.
Tank operations.

This all took two days.  The shipyard mechanic came to help us prime the system once we had got everything put back together.  There is a small hand pump on the motor between the pre-filter and the filter.  You remove a screw to open up a hole on the top of the filter to let the air escape while you pump.  We’re glad the mechanic was there, because it took a helluva long time to prime and we would have given up thinking we were doing something wrong.  But we eventually got the big belch and the fuel ran clear.

Motor running smoothly ... with no leaks !
The mechanic then turned to us and said, “I think it would be a good idea if we fired up the motor to make sure everything is running smoothly before you put it in the water.”  YES !!  We weren’t sure how to manage this ourselves and having him there to help was a great relief.  We rerouted the water intake to a bucket that we filled continuously with a hose, and with little effort, the motor started right up … and NO LEAKS !!  What a great compensation for 2 full days of really dirty work ! 

While the mechanic was still with us, Patrick brought up a recent story we’d read in the newspaper about a sailboat who’s engine began revving out of control, overheated, burned and sank the boat in a matter of minutes.  The captain had shut off the diesel to the motor, but that had no effect.  The mechanic explained that this can happen when the oil is too full, and that the only thing to do in that case is to smother the engine by blocking the air intake.  He showed us how to do this by opening up the canister of the air filter and placing a rag in the intake pipe.  But when he did this, we discovered that there was no air filter.  The wire basket that holds the filter was there, but the thin foam filter was missing.  That one truly was easy to fix, but very expensive for such a flimsy little thing.

I’m sure that the care and feeding of the marine diesel motor still holds many mysteries for us, but we certainly feel more confident after our 2 day crash course and we know that everything is now in good working order.  With only 5 days left on land (in theory) it’s great to get this out of the way.   

Posted on Sunday, August 12, 2012 | Categories:

Tuesday, 7 August 2012

Propeller Shaft Tube: The Final Chapter


It sounded so simple.  “Now that I’ve changed the propeller shaft tube and re-stratified the hull, all you guys have to do is check the alignment with the gear box, tighten all the screws and change the rubber stuffing box.”  The friend-of-a-friend who helped us with the propeller shaft tube drama left us with these cheery words of encouragement.  But we knew better (at least I did; as I’ve mentioned before, Patrick is hopelessly optimistic*).   
(*optimistic and lucky !  See Addendum to Tubed)

Of course, the shaft was not perfectly aligned with the gear box, and if the tube is already stratified in place and thus not moveable, the only other solution is to move the motor.  When the mechanic told us this, I thought it was a joke and let out a hardy belly-laugh to play along, which was promptly met with blanks stares. 

I was envisaging a huge crane with chains and winches to lift the motor off the chassis to reposition it.  In fact, all that was really needed was a small fine-tuning of the position, which is accomplished by adjusting 4 x 4 sets of screws on the engine mounts (silent blocks).  We were also told that a crow bar might be handy.  Not having a crow bar, we can report that the center support from an old beechwood IKEA table works well, too.    

The 2 "easy-to-reach" engine mounts (red circles).
Guru Bob came over to help with this task, which involved painstakingly loosening and tightening sets of screws that were both rusted and, for 2 out of 4, nearly impossible to reach.  After more than 3 hours of tweeking and several good shoves with the IKEA lever, we got something that looked pretty good.

The mechanic came over to inspect it the next morning and confirmed that it was pretty good.  But not good enough.  We were reduced to measuring the gap differences between the gear box and the intruding propeller shaft with one of those little red straws that comes with a can of WD-40.  With this fine gauged instrument, we could see that indeed there was more space on the top than the bottom.  Back to tweeking.

Patrick and I tackled it alone this time, which meant that after 2 hours of going around in circles (it's better, it's worse, it's better, it's worse), I threw down my WD-40 straw and said, “This is madness !  Let’s just PAY SOMEBODY to do this !  We’re never going to get it aligned !” to which my better half suggested that I take a little break and go work on something else.  Another hour later, he called me to come check his work, and it was nearly perfect.  We spent another few minutes fine tuning the fine tuning and decided that it just wasn’t going to get any better.  The next day, the mechanic verified our work and this time said “Not bad at all !”

Greasing the rubber stuffing box (Volvo Joint).
Patrick asked how long it takes a pro to do one of these alignments.  Our mechanic said it typically takes about 3 hours if all goes well, but he said he has taken up to 2 full days to get it right sometimes.  He gave us the green light and we tightened all the screws and connected the new rubber stuffing box.  We had anticipated having to call in for help on that task since it’s a rather important piece (the thing that keeps water from gushing into your boat through the shaft tube).  But at that point, we were so battle-worn that we just decided to do the damn thing ourselves.  We had instructions (with pictures !) and the mechanic talked us through it before hand.

And now it’s done.  The whole 2.5 month drama is finished. 

Gear box, shaft, and suffing box fixed to shaft tube: before and after.

And strangely, we don’t really feel like celebrating.  As the resident pessimist, I am waiting for the proverbial other shoe to drop, with an ever-present voice in my head saying “we’ll see, we’ll see…it’s not over yet”.  Even Patrick isn’t rushing to pop the champagne cork.  It’s hard to feel victorious when we’ve got so many other jobs ahead of us and summer is wasting away (if you dare to call 6 days without rain in 2 months “summer”).  But never fear, a big bubbly gin and tonic will mark a healthy and well-deserved pause and we’ll celebrate when we’re on the water enjoying the fruits of our labour.
Posted on Tuesday, August 07, 2012 | Categories:

Thursday, 2 August 2012

The Life Raft Conundrum


If you intend to navigate more than 6 nautical miles from shore, French regulations stipulate that you must have a life raft on board.  These rafts come compressed in containers the size of a largish suitcase and are inflated automatically by a pressurized CO2 system that is tripped by pulling a sort of rip-cord.  The rafts come in several sizes depending on the number of people on board and are equipped with emergency tools and supplies for either 1) a rescue probable within 24 hours or 2) a rescue with a wait of longer than 24 hours.  

Ours is a < 24 hour model but augmented with a grab bag containing all the items found in the > 24 hour version plus other items we don’t want to be without while bobbing around waiting for a lift. 

Life raft in container; grab bag; and deployed life raft.

The basics to add for > 24 hours are a set of emergency flares, thermal protective blankets, a first aid kit, 1 liter of water per person, and 500 grams of food rations per person.  To this, we will also add a portable VHF radio, an EPIRB (GPS emergency position-indicating radio beacon), a bailing bucket and sponges, glow sticks, a water-tight flash light, a small compass and navigation ruler, a fog horn, a sac of batteries (for flash light and radio), a fishing line, 2 baseball hats and sun screen, and photocopies of all our important papers.

And after having read the survival manual stored inside one-such life raft, you can bet that I won’t be abandoning ship without my red lipstick and pantyhose.  Now, the official story is that the lip stick is useful for writing a brief message on the limp body of your companion to signal to your rescuers exactly what is wrong with him / her in the case that he / she is air-lifted out of the raft before you.  The pantyhose, we’re told, are useful for straining the water to capture plankton for a light snack.  Frankly, I’m not buying it.  I think these two items have been suggested in a sorely misguided attempt to provide (uh-hum) “entertainment” during a possibly long wait.  (Well yes, in fact, it was a French survival manual, now that you mention it…).

So far, so good.  But the conundrum is where to store your life raft.  If you’re lucky, you boat has been designed with the life raft in mind and has its own dedicated storage space under the helmsman’s seat or in a special compartment on the transom.  Unfortunately, this is quite rare, especially on older boats, and alternatives must be found.

Of the 23 different boats we’ve sailed on, the majority simply store their life raft in the bottom of the cockpit locker.  This is a fine place for it.  It’s out of the way and in a protected location.  The only problem with this is that it is highly improbable that you will ever be able to get it out of the locker if you ever need it in a hurry (and when would you ever need it not in a hurry?).  These suckers weigh about 35 kilos (~75 pounds), and most cockpit lockers are deep, meaning that you have to get down on your knees and lean over waist-deep to even get your hands on it (after, that is, removing the bucket, the hawsers, the water hose, and the spinnaker sack that will inevitably be stored on top of it). Did I mention the saloon is on fire and you’re taking on water in a storm?

Some forward thinkers have hooked up their rafts to a pulley system that will allow them to hook one end to the boom and then hoist the raft out of the cockpit locker with the pulleys, but if you’re in an abandon-ship situation, you may not be able hook up such a system in a rush, especially if you’ve lost the mast or can’t control the boom.

The rule of thumb is that the weakest member of the crew should be able to launch the raft with one arm (the other being broken, of course).  The above-mentioned situation, even with a pulley system, won’t work for either of us.

A good method is to fix the raft to the railing of the balcony above the transom with a stainless steel support.  But your boat has to have a sufficiently strong and wide balcony to bear this weight on a rolling ship, and if you have a relatively light boat like ours (a svelte 4.5 tonnes) you have to think about balancing out all the major weights in the boat, such as the fuel tank, the water tank, etc.  Our balcony just doesn’t look strong enough or wide enough for this, and it would have to be placed on the same side as the water tank.

Our remaining option is to fix the life raft to the coach roof, in front of the companionway and behind the mast.  Here, the weight of the raft is centered and it is high relative to the surrounding deck, so it can be pushed, rather than lifted, into the water.  The drawbacks are that the coach roof was never designed to take this kind of load and depending on the boat and/or the life raft, its placement here can limit visibility forward and interfere with the boom downhaul.

Raft tied to coachroof.
When we did our test sail on Zephyr, Antoine and Caroline had the life raft rigged this way, sitting flat on a no-skid mat and wrapped up snugly with an impressive web of 20 meters of strapping.  They said it never budged during their entire trans-Atlantic voyage, despite some rough weather.  In this configuration, a good sharp knife is kept handy in the companionway to cut away the lines in a hurry.  Fortunately, the visibility forward wasn’t affected and it was low enough that it didn’t touch the boom downhaul.



Patrick and I decided that we would keep the raft on the coach roof, but that we would get fancy and buy a stainless steel support that is screwed or bolted to the deck.  The advantages are that the support offers a quick-release system and comes with a lock (since, sadly, life rafts have been known to disappear if left unlocked on the deck). 

Our raft with quick-release straps.
But after reading up on life raft positioning in the sailing forums, I had a change of heart.  Stories abound of waves and knock-downs ripping the support from the coach roof, leaving holes where the support screws used to be.  As a general rule, I don’t like putting holes, even small ones, in the boat if not absolutely necessary, so these stories sent a shiver up my spine.  On a more practical note, when we saw the system at the ship chandler’s, we noticed that the stainless steel tubes were 3 cm high.  That small 3 cm was just enough for our raft to touch the boom downhaul, and we could imagine it getting snagged each time we tacked. 

So we decided that the system of Antoine and Caroline was perfectly well-adapted to the situation after all and that we would simply use individual quick-release straps rather than a single 20 m line to fix the raft to the deck. 


We’re still trying to figure out how to add a lock system to this configuration.  A word of advice to would-be boat buyers: look carefully at the life raft placement possibilities.  This shouldn’t be an afterthought.  And don’t forget the emergency lipstick and pantyhose, either.
Posted on Thursday, August 02, 2012 | Categories:

Wednesday, 25 July 2012

A Hodge Podge of Bricolage

We have a victory to report.  If you’d told us a few months ago that we would dismantle the steering quadrant, replace the ball joint / rotator pin, and adjust the steering cable tension by ourselves, Patrick would have laughed and I would have broken down in sobs.  As it is, we’re just smugly pleased with ourselves.  (See Rainy Afternoons and Rudder Angles for the background.) 

The hopelessly stuck ball joint / rotator pin.
But the task didn’t start out so well, and if you know anything about this kind of job, you’re asking yourself, “Now why the heck did they take apart the steering quadrant just to change the ball joint?”  Because it was stuck, that’s why.  Irredeemably stuck.  So stuck that we called in the mechanic to see if we were doing something wrong.  After he tried forcing it off with a couple of screwdrivers, he told us to take apart the whole steering quadrant and bring the offending section into the shop.  There, he proceeded to attack it with a blow torch and what I think is called a hub grappler (in French, arrache-moyeux) and what I know is called a really big hammer.  

Half the steering quandrant with new joint and clean bolts.
Once the joint was replaced and all the parts were cleaned with turpentine and re-greased, putting it back together was pretty simple (although it helps to be a fan of the game Twister).

The shiny new ball joint in place.
We adjusted the tension using the screw pin connecting the steering column to the rotator pin.  By adjusting the screw pin a few turns at a time, we managed to get rid of about 2/3rds of the play in the wheel, and when we manually put the rudder straight, the wheel lined up with what we assume is the original (red) mark indicating a straight rudder.  Not too shabby.
 
We’ll keep fine-tuning to see if we can get rid of the rest of the play in the wheel, keeping in mind that “Great is the enemy of Good”.











I’ve also had a splicing fit recently:  spliced the rode to the anchor chain and made an eye splice on the other end of the rode to connect to the boat.

Chain splice and eye splice.

We installed two battery controllers (we actually only did the physical placement of them on the nav station… the electrician will come and hook them up to the batteries later).

Battery controllers installed.

And we finally tracked down a new control panel for the motor controls.

Motor control panel: before and after.

Despite this wave of activity, we’re really no closer to getting Spray into the water.  The boat yard announced that they had a backload of work and summer vacation has shut down many of their suppliers; in particular, the one who is supposed to give us an aluminium plate to reinforce the chain locker where the windlass will be placed.  We’ve got at least another 2 weeks on land.
Posted on Wednesday, July 25, 2012 | Categories: