Thursday, 20 September 2012

Whole Lotta Shakin Goin On



When Italian sailor Alex Carozzo cast off the lines in southern England to begin the first single-handed around-the-world yacht race in late October of 1968, he was so exhausted after months of overseeing the work to his boat that he anchored his 66 foot ketch, Gancia Americano, behind the Isle of Wight for a week in order to rest.  

Or so goes the Hal Roth version in The Longest Race.

I don’t believe a word of it.

We have now tried three times, unsuccessfully, to tuck Spray behind some lovely island to get some rest after months of effort, and it never works.  We can’t manage to get out of shake-down mode.

We recuperated our repaired Jib sheet after our last misadventure, and headed out this week for an appointment with a mechanic to replace the motor’s alternator and to try to figure out why the engine seems to get the burps from time to time (air in the fuel lines).  And then, we told ourselves, we would plunk down behind some lovely island and get some rest.

Stuck in the port of Crouesty
Our alternator, taken out 2 weeks ago for repairs, was still not ready, so we can look forward to another trip to the mechanic’s in another week.  For the burps, the mechanic shook his head, reassuring us that air in the system wasn’t normal, and then further comforted us by remarking that those sorts of leaks were difficult to find.  So we spent an hour blindly tightening various fittings and adding new metal collars to tighten up some connections even further.  A few test start-ups revealed no problems.  But it was too late to head off anywhere, so we stayed in port and Patrick took the opportunity to install a separate speaker for the VHF marine radio so that we can use the existing speakers for a stereo fm / CD / mp3 player.

The next morning as we were preparing to leave, the motor had great difficulty starting, and when it did, it belched out a rather startling amount of white smoke.  I suggested calling the mechanic again but Patrick declared everything to be fine (Grrrrr) and we headed off.  As luck would have it (mine, not Patrick’s) there was absolutely no wind and we had to motor all the way to the island of Houat.  At least we would be at anchor if we had engine trouble the next time.

Along the way, we tried, for the 6th time, to reset the wind speed and direction indicator to no avail, but I did manage to fix the wanky auto-pilot, who insisted on heaving over ~10 degrees anytime you turned it on.  I manually reset the rudder angle indicator arm of the pilot and then reset the controller to 0 rudder angle compensation.  There is still some play in the helm that causes the pilot to work a lot, but we have to build up the courage to fix that one, since it involves replacing the ball joint underneath the steering column.  If it is anything like the last ball joint job, we’ll need help.

Anchored at the Big Beach, Houat.

We did enjoy a lovely afternoon along the “big beach” at Houat.  It’s difficult to take in the scene with a camera.  The picture below shows a Google Earth shot of the area integrated into our navigation software (OpenCPN), where the red boat shows Spray’s position, anchored off the beach.  Patrick managed a swim (armed with a wetsuit) and I lolled around in the cockpit with my Kindle.  And the motor started right up as we prepared to head home.



OpenCPN version of Houat (red boat position not-to-scale)




We had wind for the return trip to the Gulf and even put a reef in the main (more for practice than necessity).  As we entered the Gulf, we broke a new speed record, even with a reefed mainsail: 11 knots !  We entered at the fastest period of the tidal current with a tidal coefficient of 103, which is a measure of the amplitude of the tidal range (the scale is approximately 20 to 120).  We probably had about 5 knots of current in our favour at that point.  By the time I grabbed my camera, we had descended to 10.8 knots, but trust me… we hit 11 at one point.




New speed record !

Our next few weeks will be a continuation of mini-shake-down cruises until we get all the kinks out, or at least the major ones.  Alex Carozzo headed off without doing this and had to drop out of the around-the-world race near Portugal because of a bleeding peptic ulcer.  We’ll take our time…we’re not in a race.

Sunday, 9 September 2012

First Duet

After 8 years of sailing together, last week was our first time sailing ALONE together.  We had anticipated some domestic clashes as we worked out our co-skippering routine of who-does-what-when and coped with the anxiety of being “alone”.  Friends had gleefully regaled us with stories of their first skippering experiences, and like them, I fully expected some tense, doubt-filled episodes.  In fact, there were very few clashes and surprisingly little stress, despite several rather spectacular misadventures.  

First dinner alone on boat.

We headed off for 6 days of easy cruising and rest after 3 months of non-stop work in the boatyard.  The summary of our week goes something like this:
  • 5 nights, 4 moorings, 1 port stop, 2 islands.
  • Tested the new windlass, the boom brake, and inflated the annex (dinghy) for the first time.
  • Sailed wing-on-wing with the jib sheet poled out (briefly… didn’t help).
  • Performed a “Hat Overboard” manoeuvre and recuperated the small dark object after 3 passes.
  • Learned not to succumb to peer-pressure in choosing a mooring location.  (Blindly lining up with the others isn’t necessarily what’s right for your boat.)
  • Learned that putting out an anchor buoy is a good idea to keep other boats from parking on top of your anchor, making it difficult to recuperate your anchor without a close encounter.
  • Learned that 30 meters of chain is really not enough for many fine spots in Brittany.
  • Reconfirmed that the island of Houat is breathtakingly beautiful.
  • Learned that 90 liters of fresh water goes faster than you think it does.
  • Tried to reset the wind direction and speed indicator to no avail.
  • Tried to understand the rather peculiar nature of the auto-pilot that requires one to immediately add or subtract 10 degrees depending on your tack each time it engages.
  • Mild panic attack (Patrick) when the Genoa parted from the furler and started dragging in the water while underway in a moderate swell and headwind.
  • Recuperated and immobilized a flapping headsail on the deck.
  • Put into practice our sailing school experience of installing the detachable forestay and a new headsail (a very nice 25 m2 Solent... Jib Sheet) underway, also in a moderate swell and headwind (Maria).
  • Climbed the mast (Patrick) to recuperate the headsail halyard that had remained firmly stuck to the top of the mast when the jib sheet ripped away from the shackle (in-port exercise).
  • Motor failed to start (thankfully in port) and mechanic on neighbouring boat suggested purging the fuel line to see if there was air in the system.   
  • Mild tantrum (Maria) when Patrick announced he was going to cut the fuel line to install a hand pump to make the job go faster.
  • Joy (Patrick) and panic (Maria) when motor started up after 1 hour of priming and Patrick’s insistence that all was well and good to go.
  • Learned that it isn’t enough to calculate tides and currents in order to get somewhere:  one should also calculate sunset if one wants to find a secluded mooring buoy in daylight.
Personally, I blame our misadventures on the rabbit pâté Patrick insisted on buying on Belle Ile.  Everything was going along fine until he brought it back to the boat.

When I got home, I had an email from my Dad asking what we had learned sailing alone that we hadn’t learned in all our years of sailing with others.  If one discounts my snarky, knee-jerk response that “sailing on your own boat is never a vacation”, Patrick and I would both agree that we learned to appreciate each other’s abilities in different domains.  He would not have attempted to put up a new headsail in the given conditions if I hadn’t taken the initiative, and I never would have dreamt of trying to fix the motor by myself.  Our “to do” list is now longer than when we left, and we are still desperately in need of a vacation, but we plan to head out again next week for several days … for a little rest.




Friday, 31 August 2012

Shake Down


Anytime a ship undergoes repairs or overhauls, and especially if there is a new crew aboard, it’s important to carry out a short cruise that will put the ship and her new crew through their paces in a realistic setting.  This is a Shakedown Cruise.

This week, we set off for a 3 day Shakedown Cruise in the Quiberon Bay to familiarize ourselves with Spray and her new gadgets, and to take her to the largest port in our area for repairs to the alternator.

The first task at hand, however, was to appease Neptune and the Wind Gods for our audacity of having changed the name of the boat.   

Requesting Neptune to accept a name change.
Appeasing the 4 winds.

Being a Franco-American couple, we also “cut the serpent” according to French tradition. 

Anesthetizing the serpent.

Also according to French tradition, we drank quite a lot of it ourselves !

Finally - some for us !



The Happy Couple and their newly baptized boat.

My original plan was to have a mix of hard work (day) and idyllic moorings (night).  The weather, however, had other ideas, and we were forced to duck into ports each night.  Doing this in the Quiberon Bay on the last week of August meant overcrowded and expensive port stops (Haliguen and Crouesty).  The positive aspect was that it gave us a good series of exercises for manoeuvring in close quarters, such as “parallel parking” between boats tied up 2-deep to the quay.

As the ports offered stability, electricity, and water, the work often continued well into the evenings.  Here is our list of tests / repairs carried out during Spray’s shake-down cruise:

  • Tested out-board motor and tender.
  • Installed the spray dodger.
  • Installed removable forestay for head sails.
  • Tuned rigging (shrouds, forestay, backstay, etc.).
  • Marked reef lines and main sail halyard for reef marks.
  • Verified the settings on the depth-sounder using a hand-held lead-line.   
  • Tested basic sail handling with 2 crew (tack, jibe, reef the main, change the head sails, etc.).
  • Adjusted position of the ratchet block for the Genoa furler to better control the furling line as it feeds into the drum (tended to get stuck sometimes when unfurling).
  • Adjusted clutch handle on auto-pilot.
  • Tested new windlass system.
  • Verified there were no leaks in engine filters, pumps, and propeller stuffing box after recent repairs / modifications.
  • Replaced alternator (the electrician did this).  We now have a loaner alternator and will have to go back after ours is repaired.
  • Repaired tachometer.
  • Tried valiantly to install radio fm / CD player / MP3 player.  Professional electrician declared that the radio was wired correctly and was most probably broken.  Return to supplier.
  • Identified and documented all the electrical connections hiding behind the chart table control panel (Guru Bob bravely did this…).
  • Tested navigation software (OpenCPN) with GPS and AIS systems.
  • Tested “anchor watch” system of OpenCPN.
  • Tested wifi antenna (most excellent) and managed to Skype home to Jacksonville, Florida using only wifi on the boat.  Pretty dang cool.
  • Picked Guru Bob’s brains and 30+ years experienced to identify the best mooring spots along the coast and islands.

Just before heading back to our home mooring buoy, we finally managed a calm anchorage for lunch (and to test the windlass).  This shake-down cruise has given us confidence in the boat and her equipment and increased our frustration at not having the time or the appropriate weather to enjoy the many beautiful mooring sites around the islands that rim the Quiberon Bay. But next week, a high-pressure system is supposed to be sitting comfortably near, and we fully intend to head out for some island hopping !

 
Patchew at the helm.


More tranquil moorings in our near future.

Friday, 24 August 2012

Afloat !



Spray was launched this morning at 11 am and is resting comfortably (we hope) on her mooring in the Auray River.  Everything went smoothly, despite scattered showers and a stiff breeze.

Spray hanging from her ball in the Auray River.
We now believe what we have been told: if you wait until everything is perfect to put the boat in the water, you’ll never put the boat in the water.  At least our remaining problems are not ones that require the boat to be on dry land.  

Since the last update, our gremlins continue to play hide-and-seek.  Two days ago as we were putting on the last coat of bottom paint, we noticed that the joint around the keel was still sticky and gooey.  After 2 months of drying time, we thought this a bit odd and called the boatyard guys to check it out.  They declared that the sealant had failed to cure, which, according to the Sika company, is a “phenomena” that happens in about 1 in 10 batches.  (Now honestly, is a known, regular 10% frequency really a phenomenon?)  That was easy enough to fix but fortunately we had already postponed the launch date.

Our last big mystery is the alternator failing to charge the batteries.  The electrician said he’d never seen anything like it, and suspects the regulator.  We have a date next Wednesday with the experts in Crouesty, the largest port in the Gulf of Morbihan area.  Fortunately, it’s something that can be fixed with the boat in the water, so no excuse for a launch delay.

3 burners with 30mbar pressure regulator.


The gas stove now works with our new French fittings.  We had anticipated not being able to use all 3 burners at the same time, since the new pressure regulator is 30mbar and the original German one was 50mbar, but when we fired up the burners, we got a good strong flame out of all 3.  Crazy Germans.  (wink at MV !)





The bow plate has been installed (zoom in on 1st photo above) and we added an anchor-chain connector (Junction KONG) so that the chain and anchor retract smoothly in the bow roller.  Because the hole in the anchor stock was not a simple round hole but an oblong one, the junction tended to slide down when not under strain, so we had to fill the hole with some clever seamanship.  Time will tell if it holds up to chaffing, but it works well for now.

Anchor-chain connector.
We finally removed the last 2 names of the boat from the transom (Zephyr and Er Gwennick) and put the SPRAY sticker in place.  We opted for a metallic silver color that we thought would be evocative of sea spray shining in the sun, and unfortunately this is the case, rendering it a bit hard to see when the sun hits it at a certain angle.  We also renamed the life buoy but I suspect Zephyr is still written on the inflatable annexe.  A battle for another day.

SPRAY !
And for our next trick, 3 days of REST !  We’ve been working very long days non-stop for the last 3 months and my body’s alternator, like Spray’s, has entirely failed to recharge my batteries. 

A big thanks to all who gave advice, equipment, and a helping hand in getting Spray into the water over the last 3 months:  Antoine and Caroline, Remi, Daniel, Roland, the Le Borgne Crew (Nicolas, Patrick, Yves, Alain, Eric, Betty, et Helene), the E3 electricians Patrick and Philippe, Jacques (we tested out the annexe this morning - it's perfect - thank you !), and last but foremost, Guru Bob.

Posted on Friday, August 24, 2012 | Categories:

Saturday, 18 August 2012

Launch Scuttled by Euro-Gremlins


Mark my words: Europe is doomed.  Forget harmonization of social security, retirement, and the minimum wage.  The problems run much deeper, like the fact that German screw threads turn to the right, and French screw threads turn to the left.  I haven’t had the time to investigate further, but at first glance, it appears that most of the Anglo-Saxon EU countries follow Germany’s lead, while the Latin “Club Med” countries stick with France.  I’m sure a closer investigation would reveal pocket alliances resembling the voting in the Eurovision Song Contest  (For non-European friends unfamiliar with Eurovision, it’s uncomfortably like the Gong Show without the gong.)

We discovered this charming example of regional diversity whilst trying to re-plumb our cooking gas lines.  The original fittings were so rusted that it was hard to tell where one nut ended and the next one began, and so we decided to change them all.  A word to the wise who find themselves in a similar situation:  DON’T.  Rust is also known as “the poor man’s Loctite” and that original rusty system probably had less chance of leaking than the new one we planned to install. 

The connection to the copper tubing was still good and we had hoped to use the same pressure regulator.  Long story short:  After 7 visits to different hardware, plumbing, boating and camping stores, the answer was nyet.  The hoses and fittings we buy in France cannot be made to work with the original German fittings.  We have now a shiny new French system, where the next challenge is to make this French system fit in the gas tank compartment of the German boat.  This will involve drilling a new hole in the compartment and bending / aligning the copper tubing that runs to the stove. 

Yoga helps, too.
The next bugaboo was the electrical system.  I realized that working with gas and electricity made me nostalgic for those sweet simple days of working on the engine.  Engines are fairly straightforward beasts, and there are lots of technical books to help you.  Every country, nay, every boat owner, seems to want to put his personal stamp on the electrical and gas systems, and there is no way to know what they’ve done or why … just a mass of multi-colored spaghetti with strands trailing off behind bulkheads, never to be seen again.  We have the original German wiring diagram, but after 20 years in the hands of 2 different French owners, there is little resemblance.  To keep things really fun, nothing has been labelled. 

After a nervous hour of trying to figure out why the service batteries were no longer feeding any of the instruments, we discovered that the system is outfitted with a fuse that had blown.  How or when it had blown is still a mystery, but at least the problem was easy to resolve.  We debated putting in a breaker switch instead of using fuses, but the smallest breaker available was 60 amps, which we thought was probably too high to give much protection.  Next, we realized that the 220V recharging system was wired to the control panel rather than directly to the battery, meaning that the batteries would only be recharged if the circuit breakers were closed.  Why?  Fixed that. 

The major problem du jour is that the alternator is not charging the batteries.  The alternator works fine and the recharger works fine, and when wired together correctly, the system works fine.  But the system is not wired correctly and none of the motor controls function except the ignition alarm.  The electrician we worked with yesterday gave up at 8 p.m., apologetically announced that he had to go on vacation, and gave us the telephone number of a colleague who might be able to help us.    

The original launch date was based on finalizing our major refits, namely the propeller shaft tube and the windlass, both of which are now done.

Reinforcing and stratifying the forward part of the chain locker.
Windlass and foot controls in place, chain marked every 5 meters.

However, our lesser tasks, by their number (33) and “regional diversity issues”, have now become a force to be reckoned with, and the launch has been postponed for one week.  Looking over my list, I’m wondering how many more Gremlins are lurking.
Posted on Saturday, August 18, 2012 | Categories: